Jump to content

SOLD
 
Helix DSP Processor
- Cash & Carry
Condition
Very Good [4/5]
Suitable For
All Models
Posted on: 26 Feb 2023 | Updated on : 05 Apr 2023

Merchant information

81 Ubi Avenue 4 #01-10 UB. One S(408830)
9.30am - 7.30pm (Mon - Sat)
64440123
81388731

Ad information

The first stand-alone DSP that deserves to be called a HELIX. The new Helix DSP is more than convincing proof that noisy, distorting sound processors are finally a thing of the past. Excellent technical specs are combined with a feature package that could hardly be more impressive in actual practice. Intuitive operation thanks to a clearly structured graphical PC interface enables any ambitious sound freak to optimise the sound virtually any which way.

Features

  • Powerful "fixed point" Audio DSP with 56 Bit resolution
  • Freely configurable inputs and outputs with flexible signal summing options
  • Paragraphic 30-band EQ per channel with ultra-precise 0.25 dB steps
  • Time-alignment adjustment in narrow 7 mm steps and phase control in 11.25° steps
  • Various high- and lowpass filter characteristics with 6 - 30 dB slope available
  • Different signal routing matrices for each signal input section including configurable signal detections
  • "Ground lift" switch to avoid ground loops
  • Control input for connecting remote controls and accessories
  • Easy configuration thanks to the professional and user-friendly DSP PC-Tool Version 3 software


Power Save Mode
The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the Helix DSP once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with "CAN" or any other internal bus structures it may happen that the radio remains "invisibly" turned on for up to 45 min. even after leaving the car! Once the “Power Save Mode is active the "Remote Output" and therefore the connected amplifiers will be turned off. The HELIX DSP will reactivate the “Remote Output” within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save made” via the DSP PC-Tool software.

Start-Stop capability
The switched power supply of the Helix DSP assures a constant internal supply voltage even if the battery's voltage drops to 6 Volts during engine crank.

Automatic Digital Signal Detection
Switching from analog input to the digital input is done automatically as soon as an signal is detected on the optical input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can use the optional cable remote control URC 2A for manual switching between analog and digital inputs.

Specifications

Inputs :6 x RCA

  • 4 x Highlevel speaker input
  • 1 x Optical SPDIF-Format (6-96 kHz Sampling Rate)
  • 1 x Remote In

Input sensitivity :

  • RCA/Cinch 4 Volts (internally adjustable) - default 4 Volts
  • Highlevel 5 - 11 Volts (intern. adjustable) - default 11 Volts
  • (corresponds to 6 - 30 Watts RMS - not max. power)

Outputs :

  • 8 x RCA
  • 1 x Remote Out

Output voltage :

  • Max. 4 Volts RMS

Frequency response :

  • 10 Hz - 22,000 Hz

DSP resolution :

  • 56 Bit

DSP processing power :

  • 172 MHz

DSP type :

  • Audio signal processor

Signal converter :

  • A/D: BurrBrown
  • D/A: BurrBrown

Signal-to-noise ratio - digital input :112 dB (A-weighted)
Signal-to-noise ratio - analog input :107 dB (A-weighted)

Total harmonic distortion (THD+N) - digital input :< 0.001 %
Total harmonic distortion (THD+N) - analog input :< 0.003 %

IM distortion (IMD) - digital input :< 0.003 %
IM distortion (IMD) - analog input :< 0.007 %

Crosstalk :> 90 dB @ 10 kHz

Operating Voltage :9.6 - 18 Volts, short drops down to 6 Volts acceptable

Current draw :< 450 mA

Dimensions (H x W x D) :40 x 177 x 120 mm / 1.6 x 7 x 4.75“

Contact (Whatsapp): 81388731
Facebook: https://www.facebook.com/AudioSolutionPteLtd/

 
1564380951.jpg

Ad information

The first stand-alone DSP that deserves to be called a HELIX. The new Helix DSP is more than convincing proof that noisy, distorting sound processors are finally a thing of the past. Excellent technical specs are combined with a feature package that could hardly be more impressive in actual practice. Intuitive operation thanks to a clearly structured graphical PC interface enables any ambitious sound freak to optimise the sound virtually any which way.

Features

  • Powerful "fixed point" Audio DSP with 56 Bit resolution
  • Freely configurable inputs and outputs with flexible signal summing options
  • Paragraphic 30-band EQ per channel with ultra-precise 0.25 dB steps
  • Time-alignment adjustment in narrow 7 mm steps and phase control in 11.25° steps
  • Various high- and lowpass filter characteristics with 6 - 30 dB slope available
  • Different signal routing matrices for each signal input section including configurable signal detections
  • "Ground lift" switch to avoid ground loops
  • Control input for connecting remote controls and accessories
  • Easy configuration thanks to the professional and user-friendly DSP PC-Tool Version 3 software


Power Save Mode
The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the Helix DSP once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with "CAN" or any other internal bus structures it may happen that the radio remains "invisibly" turned on for up to 45 min. even after leaving the car! Once the “Power Save Mode is active the "Remote Output" and therefore the connected amplifiers will be turned off. The HELIX DSP will reactivate the “Remote Output” within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save made” via the DSP PC-Tool software.

Start-Stop capability
The switched power supply of the Helix DSP assures a constant internal supply voltage even if the battery's voltage drops to 6 Volts during engine crank.

Automatic Digital Signal Detection
Switching from analog input to the digital input is done automatically as soon as an signal is detected on the optical input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can use the optional cable remote control URC 2A for manual switching between analog and digital inputs.

Specifications

Inputs :6 x RCA

  • 4 x Highlevel speaker input
  • 1 x Optical SPDIF-Format (6-96 kHz Sampling Rate)
  • 1 x Remote In

Input sensitivity :

  • RCA/Cinch 4 Volts (internally adjustable) - default 4 Volts
  • Highlevel 5 - 11 Volts (intern. adjustable) - default 11 Volts
  • (corresponds to 6 - 30 Watts RMS - not max. power)

Outputs :

  • 8 x RCA
  • 1 x Remote Out

Output voltage :

  • Max. 4 Volts RMS

Frequency response :

  • 10 Hz - 22,000 Hz

DSP resolution :

  • 56 Bit

DSP processing power :

  • 172 MHz

DSP type :

  • Audio signal processor

Signal converter :

  • A/D: BurrBrown
  • D/A: BurrBrown

Signal-to-noise ratio - digital input :112 dB (A-weighted)
Signal-to-noise ratio - analog input :107 dB (A-weighted)

Total harmonic distortion (THD+N) - digital input :< 0.001 %
Total harmonic distortion (THD+N) - analog input :< 0.003 %

IM distortion (IMD) - digital input :< 0.003 %
IM distortion (IMD) - analog input :< 0.007 %

Crosstalk :> 90 dB @ 10 kHz

Operating Voltage :9.6 - 18 Volts, short drops down to 6 Volts acceptable

Current draw :< 450 mA

Dimensions (H x W x D) :40 x 177 x 120 mm / 1.6 x 7 x 4.75“

Merchant information

81 Ubi Avenue 4 #01-10UB. One S(408830)
9.30am - 7.30pm (Mon - Sat)
64440123 / 81388731
Posted on: 26 Feb 2023 | Updated on : 05 Apr 2023

Features & specs

The first stand-alone DSP that deserves to be called a HELIX. The new Helix DSP is more than convincing proof that noisy, distorting sound processors are finally a thing of the past. Excellent technical specs are combined with a feature package that could hardly be more impressive in actual practice. Intuitive operation thanks to a clearly structured graphical PC interface enables any ambitious sound freak to optimise the sound virtually any which way.

 

Features

  • Powerful "fixed point" Audio DSP with 56 Bit resolution
  • Freely configurable inputs and outputs with flexible signal summing options
  • Paragraphic 30-band EQ per channel with ultra-precise 0.25 dB steps
  • Time-alignment adjustment in narrow 7 mm steps and phase control in 11.25° steps
  • Various high- and lowpass filter characteristics with 6 - 30 dB slope available
  • Different signal routing matrices for each signal input section including configurable signal detections
  • "Ground lift" switch to avoid ground loops
  • Control input for connecting remote controls and accessories
  • Easy configuration thanks to the professional and user-friendly DSP PC-Tool Version 3 software

Power Save Mode

The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the Helix DSP once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with "CAN" or any other internal bus structures it may happen that the radio remains "invisibly" turned on for up to 45 min. even after leaving the car! Once the “Power Save Mode is active the "Remote Output" and therefore the connected amplifiers will be turned off. The HELIX DSP will reactivate the “Remote Output” within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save made” via the DSP PC-Tool software.

 

Start-Stop capability

The switched power supply of the Helix DSP assures a constant internal supply voltage even if the battery's voltage drops to 6 Volts during engine crank.

 

Automatic Digital Signal Detection

Switching from analog input to the digital input is done automatically as soon as an signal is detected on the optical input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can use the optional cable remote control URC 2A for manual switching between analog and digital inputs.

 

Specifications

Inputs :6 x RCA
4 x Highlevel speaker input
1 x Optical SPDIF-Format (6-96 kHz Sampling Rate)
1 x Remote In
Input sensitivity :RCA/Cinch 4 Volts (internally adjustable) - default 4 Volts
Highlevel 5 - 11 Volts (intern. adjustable) - default 11 Volts
(corresponds to 6 - 30 Watts RMS - not max. power)
Outputs :8 x RCA
1 x Remote Out
Output voltage :Max. 4 Volts RMS
Frequency response :10 Hz - 22,000 Hz
DSP resolution :56 Bit
DSP processing power :172 MHz
DSP type :Audio signal processor
Signal converter :A/D: BurrBrown
D/A: BurrBrown
Signal-to-noise ratio - digital input :
Signal-to-noise ratio - analog input :
112 dB (A-weighted)
107 dB (A-weighted)
Total harmonic distortion (THD+N) - digital input :
Total harmonic distortion (THD+N) - analog input :
< 0.001 %
< 0.003 %
IM distortion (IMD) - digital input :
IM distortion (IMD) - analog input :
< 0.003 %
< 0.007 %
Crosstalk :> 90 dB @ 10 kHz
Operating Voltage :9.6 - 18 Volts, short drops down to 6 Volts acceptable
Current draw :< 450 mA
Dimensions (H x W x D) :40 x 177 x 120 mm / 1.6 x 7 x 4.75“
Consumer Reviews
This is a must have if going for high end audiophile. Able to perform professional tuning and produce crisp audio
Reviewed by coolbluepica 

Similar Items

Related Searches : Processor

Email Enquiry

This enquiry will be sent directly to the seller.
* indicates compulsory field.
×
×
  • Create New...