Amazon777 3rd Gear November 10, 2012 Share November 10, 2012 I guess I will go purchase from AD and ask them install, hopefully they provide the installation.. Was at Kah Motor Ubi today and saw display of ITB100HD, guess KM should be providing installation for it's customer as well. Not sure about Borneo ↡ Advertisement Link to post Share on other sites More sharing options...
Surge Neutral Newbie November 10, 2012 Share November 10, 2012 What is the recommended cut-off voltage for the following setup? Using Itronics ITB100HD for front only with Itronics power magic Currently set on cut-off at 11.8V and time limit is the default( not sure if default is 12hrs anot) Is this ok?? Link to post Share on other sites More sharing options...
Weewee1976 3rd Gear November 10, 2012 Share November 10, 2012 What is the recommended cut-off voltage for the following setup? Using Itronics ITB100HD for front only with Itronics power magic Currently set on cut-off at 11.8V and time limit is the default( not sure if default is 12hrs anot) Is this ok?? I set 12V and 48hrs for my PM Pro. Link to post Share on other sites More sharing options...
Refresher76 Clutched November 10, 2012 Author Share November 10, 2012 What is the recommended cut-off voltage for the following setup? Using Itronics ITB100HD for front only with Itronics power magic Currently set on cut-off at 11.8V and time limit is the default( not sure if default is 12hrs anot) Is this ok?? I am using this setting. No issue at all. Link to post Share on other sites More sharing options...
Refresher76 Clutched November 10, 2012 Author Share November 10, 2012 What is the recommended cut-off voltage for the following setup? Using Itronics ITB100HD for front only with Itronics power magic Currently set on cut-off at 11.8V and time limit is the default( not sure if default is 12hrs anot) Is this ok?? I am using this setting. No issue at all. Link to post Share on other sites More sharing options...
Refresher76 Clutched November 10, 2012 Author Share November 10, 2012 What is the recommended cut-off voltage for the following setup? Using Itronics ITB100HD for front only with Itronics power magic Currently set on cut-off at 11.8V and time limit is the default( not sure if default is 12hrs anot) Is this ok?? I am using this setting. No issue at all. Link to post Share on other sites More sharing options...
Tripleh 1st Gear November 11, 2012 Share November 11, 2012 I find the unit quite hot after half an hour of operation, Is it normal? Link to post Share on other sites More sharing options...
Tripleh 1st Gear November 11, 2012 Share November 11, 2012 (edited) #double post# Edited November 11, 2012 by Tripleh Link to post Share on other sites More sharing options...
RageX 1st Gear November 11, 2012 Share November 11, 2012 I find the unit quite hot after half an hour of operation, Is it normal? Yes it does get somewhat hot... Link to post Share on other sites More sharing options...
Unclepigpig 1st Gear November 11, 2012 Share November 11, 2012 Finally installed my ebay *ahem* purchased itb100 . Realised that there is no recording for my trip back home this afternoon despite card showing i have more than 20gb space avaiable. It stopped recording halfway during the morning trip. Anyone has a similar encounter? Am using my old transend 32gb class 6 card. Link to post Share on other sites More sharing options...
RageX 1st Gear November 11, 2012 Share November 11, 2012 Finally installed my ebay *ahem* purchased itb100 . Realised that there is no recording for my trip back home this afternoon despite card showing i have more than 20gb space avaiable. It stopped recording halfway during the morning trip. Anyone has a similar encounter? Am using my old transend 32gb class 6 card. Any error noise? Is the red light on the cam lighted up? Try reformatting the card. Link to post Share on other sites More sharing options...
Refresher76 Clutched November 11, 2012 Author Share November 11, 2012 Any error noise? Is the red light on the cam lighted up? Try reformatting the card. Me too make a silly mistake. I unplugged my power cable. Then plugged back, insert into the video output hole. End up no video recording.. Link to post Share on other sites More sharing options...
Zhutou Clutched November 11, 2012 Share November 11, 2012 I find the unit quite hot after half an hour of operation, Is it normal? ya normal most likely due to full hd recording and gps Link to post Share on other sites More sharing options...
Vsafe Neutral Newbie November 12, 2012 Share November 12, 2012 bump Link to post Share on other sites More sharing options...
Tripleh 1st Gear November 12, 2012 Share November 12, 2012 One more question. What is the safe way to remove the SD memory card when the unit is connected to the uninterrupted power supply? How do I switch off the unit before I remove the memory card? the manual says "do not remove the power source or pull out the SD memory card from the product when recording the data into SD memory card. This may cause the loss of data and damage to the SD memory card" Link to post Share on other sites More sharing options...
Zhutou Clutched November 12, 2012 Share November 12, 2012 One more question. What is the safe way to remove the SD memory card when the unit is connected to the uninterrupted power supply? How do I switch off the unit before I remove the memory card? the manual says "do not remove the power source or pull out the SD memory card from the product when recording the data into SD memory card. This may cause the loss of data and damage to the SD memory card" Plug out the power cable from the dvr before removing the sdcard Link to post Share on other sites More sharing options...
Adrianli Hypersonic November 13, 2012 Share November 13, 2012 One more question. What is the safe way to remove the SD memory card when the unit is connected to the uninterrupted power supply? How do I switch off the unit before I remove the memory card? the manual says "do not remove the power source or pull out the SD memory card from the product when recording the data into SD memory card. This may cause the loss of data and damage to the SD memory card" This type of question also can??? Its like asking how to remove the sh1t from my a$$. Just pull down ur shorts + underwear lah. Link to post Share on other sites More sharing options...
Patience Clutched November 13, 2012 Share November 13, 2012 (edited) Plug out the power cable from the dvr before removing the sdcard after removing the cable, wait for the the red light to go off then remove the card. Edited November 13, 2012 by Patience ↡ Advertisement Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In NowRelated Discussions
Related Discussions
Feedback
Feedback
How to feedback on hospital service?
How to feedback on hospital service?
Seen the new look on Sgcarmart's Used Car pages? Love it or hate it? We want to hear from you!
Seen the new look on Sgcarmart's Used Car pages? Love it or hate it? We want to hear from you!
Anyone have invested in SSB?
Anyone have invested in SSB?
Feedback on hazard
Feedback on hazard
Cannot post an Ad
Cannot post an Ad
Any feedback on castlewoodgroup?
Any feedback on castlewoodgroup?
VW Tiguan 2011-2012 feedback
VW Tiguan 2011-2012 feedback